Power options for your dash cam (updated guide)
Updated guide. Dash cams have changed a lot since the early 2010s, but the question of how to power one hasn’t. Here are the main options in 2026, what each is good for, and when to get an auto electrician involved.
A dash cam is only useful if it’s recording when something happens. Most “it didn’t record” stories come down to power: a loose cigarette-lighter plug, a camera that shut off when the ignition did, or a parking mode that flattened the car battery and was then switched off for good. Choosing the right power setup avoids all three.
Option 1: 12V accessory socket (cigarette lighter)
Every dash cam comes with a plug for the 12V accessory socket. It’s the simplest setup: plug in, tuck the cable along the headliner and down the A-pillar, done.
- Good for: renters, leased cars, swapping the camera between vehicles, or trying a dash cam before committing.
- Downsides: occupies the socket, the plug can work loose over bumps, and in most cars the socket switches off with the ignition, so there’s no recording while parked. In some cars the socket stays live all the time, which can drain the battery if the camera is left on.
Tip: run the cable around the edge of the windscreen and along the door seal rather than across the dash. Keep it clear of the airbag cover on the A-pillar, as a curtain airbag can deploy along that line.
Option 2: USB socket
Many newer cars have USB-A or USB-C ports, and some dash cams run happily from them. Check the camera’s power requirements first. Some built-in USB ports only supply 0.5–1 amp, which isn’t enough for a camera with a large screen or a rear camera attached, and can cause random reboots. Some ports are also data-only.
Option 3: Hardwire kit to the fuse box
A hardwire kit connects the camera directly to the car’s fuse box using fuse taps. It frees up the 12V socket, hides the cable completely, and enables parking mode, which records bumps or motion while the car is parked.
A typical kit has three wires:
- Constant (battery) wire: connected to a fuse that’s live all the time. Powers the camera when parked.
- ACC (ignition) wire: connected to a fuse that’s only live with the ignition on. Tells the camera when you’re driving.
- Ground: connected to a bare metal bolt on the chassis.
A good kit includes a low-voltage cut-off: it switches the camera off if the battery drops below a set level (commonly selectable around 11.8–12.4V on 12V systems) so you can still start the car. Set it conservatively at first, especially in winter or if the car sits for days at a time.
Fuse tapping looks easy in videos, but it’s also where most problems start: tapping the wrong fuse (an airbag or ECU circuit), poor earth connections, or a fuse tap rated wrongly for the slot. If you’re not confident identifying circuits with a multimeter, have an auto electrician or a specialist installer do it. Expect to pay roughly $100 – $250 for a front camera hardwire install, more with a rear camera.
Option 4: OBD-II power cable
An OBD power cable plugs into the diagnostic port under the dash and provides constant and switched power without touching the fuse box. It’s a tidy plug-and-play option, especially in leased or newer cars.
- Check compatibility for your make and model. Some cars cut power to the OBD port, others keep it live constantly.
- Make sure the cable has a low-voltage cut-off.
- The plug can be knocked by your knee in some cars; secure the cable with ties.
Option 5: Dedicated dash cam battery pack
A separate lithium battery pack (usually LiFePO4) charges while you drive and powers the camera when parked, so parking mode never touches the car’s starter battery. Common sizes give anywhere from several hours to a couple of days of parking recording.
- Good for: people who want long parking-mode recording, cars with start-stop or sensitive electrical systems, and anyone worried about warranty or battery drain.
- Downsides: extra cost (typically $250 – $600), and it needs mounting under a seat or in the console.
Choose a pack with LiFePO4 chemistry and proper heat protection. Cabin temperatures in an Australian summer can exceed 60°C, which is hard on any battery.
What about hybrids and EVs?
Hybrid and electric vehicles still have a 12V battery that runs accessories, but it’s often smaller than in a petrol car and some vehicles put the 12V system to sleep aggressively. Parking mode on the 12V battery can trigger warnings or leave you unable to “start” the car. A dedicated battery pack, or the manufacturer’s own accessory power options, is the safer route. If unsure, ask the dealer or an auto electrician familiar with your model.
Heat and the camera itself
Power isn’t the only thing that fails in summer. Cameras with a lithium-ion battery inside can swell and fail in parked cars. Supercapacitor-based cameras handle heat far better and are worth paying a little extra for in Australian conditions. Mount the camera behind the rear-view mirror where it’s partly shaded.
Quick comparison
| Method | Parking mode | Install difficulty | Typical cost |
|---|---|---|---|
| 12V socket | Usually no | Very easy | Included |
| USB port | Usually no | Very easy | Included |
| Hardwire kit | Yes | Moderate | $25 – $50 kit, $100 – $250 installed |
| OBD cable | Yes | Easy | $30 – $70 |
| Battery pack | Yes, longest | Moderate | $250 – $600 |
Questions to ask an installer
- Which fuses will you tap, and are any safety-related circuits involved?
- Where will you earth the kit?
- What low-voltage cut-off will you set?
- Will the cable routing stay clear of the curtain airbags?
- Does the install affect my vehicle warranty?
More car and 12-volt guides are in our Car & 12V section.